1 scope this specification shall cover the characteri stics of the ceramic resonator with the type ztacc3.58mg. 2 part no. part number customer part no specification no ztacc3.58mg 3 outline drawing and dimensions 3.1 appearance: no visible damage and dirt. 3.2 except the chip(ceramic element, ceramic base, capacitance slice), the materials don?t contain lead. 3.3 dimensions output input unitmm 3.40.3 7.40.3 5.00.3 1.80.3 1.20.3 1.20.3 3.58m 4 rating and electrical specifications http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
4.1 rating items content withstanding voltage (v) 50 (dc 1min) insulation resistance ri, m ? min. 100 100v 1min operating temperature range ( ) -20 +80 storage temperature range ( ) -55 +85 4.2 electrical specifications oscillation frequency fosc mhz 3.580 frequency accuracy % 0.5 resonant impedance ro ? max. 30 temperature coefficient of oscillation frequency % max. 0.3 oscillation frequency drift -20 +80 rating voltage ur v max. 6v dc 15v p-p aging rate % max. 0.3 for ten years 5 measurement 5.1 measurement conditions parts shall be measured under a condition ( temp. 20 15 ,humidity 65%20% r.h.) unless the standard condition(temp. 25 3 ,humidity 65%5% r.h.) is regu lated to measure. 5.2 test circuit 6 physical and environmental characteristics no item condition of test performance requirements ic 1/6tc4069ubp2 x:ceramic resonator c1,c2: 30pf http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
6.1 humidity keep the resonator at 40 2 and 90%-95% rh for 96h4h. then release the resonator into the room condition for 1h prior to the measurement. it shall fulfill the specifications in table 1. 6.2 vibration subject the resonator to vibration for 2h each in x y and z axis with the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10 hz?55hz. it shall fulfill the specifications in table 1. 6.3 mechanical shock drop the resonator randomly onto a wooden floor from the height of 100cm 3 times. it shall fulfill the specifications in table 1. 6.4 soldering test passed through the re -flow oven under the following condition and left at room temperature for 1h before measurement. it shall fulfill the specifications in table 1. temperature at the surface of the substrate time preheat 150 5 60s10 s peak 260 5 10s3 s 6.5 solder ability dipped in 250 5 solder bath for 3s0.5 s with rosin flux (25wt% ethanol solution.) the terminals shall be at least 95% covered by solder. 6.6 high temperature exposure subject the resonator to 80 5 for 96s, then release the resonator into the room conditions for 1h prior to the measurement. it shall fulfill the specifications in table 1. 6.7 low temperature exposure subject the resonator to -20 5 for 96h, then release the resonator into the room conditions for 1h prior to the measurement. it shall fulfill the specifications in table 1. to be continued 6 physical and environmenal characterisics no item condition of test performance requirements 6.8 temperature subject the resonator to -40 for 30 it shall fulfill the http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
cycling min. followed by a high temperature of 85 for 30 min. cycling shall be repeated 5 times with a transfer time of 15s. at the room temperature for 1h prior to the measurement. specifications in table 1. 6.9 board bending mount a glass-epoxy board (width=40mm,thickness=1.6mm),then bend it to 1mm displacement and keep it for 5s. (see the following figure) support bar press head press mechanical damage such as breaks shall not occur. table 1 item specification after test oscillation frequency change fosc/fosc (%) max 0.3 resonant impedance ( ) max 40 the limits in the above table are refe renced to the initial measurements. 7 recommended land pattern and reflow soldering standard conditions 7.1recommended land pattern http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
7.2recommended reflow soldering standard conditions peak:260 250 255 pre-heating within 10s within 80-120s. within 20-40s tem.() 8 package to protect the products in storage and transportation it is necessary to pack them outer and inner package .on paper pack, the following requirements are requested. 8.1 dimensions and mark http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
at the end of package, the warning (moist ure proof, upward put) s hould be stick to it. dimensions and mark (see below) 8.2 section of package package is made of corrugated paper with thickness of 0.8cm.package has 10 inner boxes, each box has 1 reel(each reel for plastic bag) 8.3 quantity of package per plastic reel 4000 piec es of piezoelectr ic ceramic part per inner box 1 reel no. name quantity notes 1 package 1 2 certificate of approval 1 3 label 1 4 tying 2 5 adhesive tape 1.2m 6 belt 2.9m 7 inner box 10 http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
per package 10 inner boxes 40000 pieces of piezoelectric ceramic part 8.4 inner packing dimensions 1 label 2 qc label 3 inner box pars shall be packaged in box with hol d down tape upside. part no., quantity and lot no. 8.5 reel http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
dimensions unitmm a b w t pieces per reel carrier tape size 330 3 80min 16.4min 22.4max 4000typ. 16 8.6 taping dimensions 8.7 packing method sketch map http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
leader 200mm max loaded pocket blank pocket 10 pitches blank pocket 10 pitches 8.8 test condition of peeling strength 10 max top tape p e e l i n g s t r e n g t h 2 0 - 7 0 g carrier tape 9 other 9.1 caution of use 9.1.1 do not use this product with bend. pleas e don?t apply excess mechanical stress to the component and terminals at soldering. 9.1.2 the component may be damaged when an excess stress will be applied. 9.1.3 this specification mentions the quality of the component as a single unit. please insure the component is thoroughly eval uated in your application circuit. 9.2 notice 9.2.1 please return one of this specifica tion after your signatu re of acceptance. 9.2.2 when something gets doubtful with this specifications, we shall jointly work to get an agreement. http://www.luguang.cn email:lge@luguang.cn ztacc3.58mg
|
